Aeware Controllers
IN.Xm TechBook
IN.Xm Quick configuration Card
IN.Xe TechBook
IN.Xe Infield Low Level Programming Manual
IN.Y (series)
in.xe Programming Procedure
Touchpads
in.k100
in.k200
in.k400
in.k450 (in.xe)
in.k450 (in.xm)
in.k600 (in.xe)
in.k600 (in.xm)
in.k8
in.touch Tech Book
in.k19
in.k35
| IN.Xe Swim Spa Slave | |
| Code | Fault |
| Hr or Hr2 | Internal hardware error |
| Prr or Pr2 | Temperature sensor failure |
| HL or HL2 | Hi-limit (Water has reached 48c or 119F) |
| FLO or FL2 | Flow error |
| UPL | No low level configuration software in system |
| AOH or AO2 | Temperature in the spa pack is too hot |
| OH or OH2 | Water over temperature (Water has reached 43c or106F) |
| IN.Xe Swim Spa | |
| Code | Fault |
| Er1 | Communication between master & slave doesn’t work |
| SLA | The pack on which the main keypad is connected is a SLAVE |
| LL- – | Unable to select the desired low level (when you confirm it goes back into the low level menu) |
| LLEr | The selected configuration is not a swim spa configuration and a SLAVE pack has been detected |
| IN.Xe Others | |
| Code | Fault |
| Stby | Standby mode |
| OFF | 30 Min all out puts off |
| FX or FF- – | Filter cycle frequency per day |
| FS- – | Filter cycle start time |
| Fdx- -or d- | Filter duration in hours |
| EP 0 or EP 1 | Economy mode on/off |
| ES- – | Economy mode start time |
| ED- – | Economy mode duration in hours |
| EE- – | Economy mode end time |
| Econ | Economy mode set |
| rLY | Stuck relay |
| IN.Xm | |
| Code | Fault |
| SPHr | A hardware error was detected in the controller |
| SPoT | The controller’s internal temperature is too hot |
| SPIn | The Input Voltage is too low |
| SPF1 | Fuse #1 is blown |
| SPF2 | Fuse #2 is blown |
| SPF3 | Fuse #3 is blown |
| SPbr | Incorrect breaks size set |
| SPoH | Over heat (Water has reached 48c or 119F) |
| rHHr | A hardware error was detected in the in.therm (Heater) |
| rHnH | Heater is trying to heat, but no rise in temperature rise detected (Not heating) |
| rHnF | No flow detected |
| rHnC | Communication error between the controller and heater |
| rHHL | High limit circuit tripped |
| rHPr | Temperature probe Failure |
| rHID | The id number between heater and controller don’t match (Wrong model) |
| P1Er | No detection of current change when turning on and off (Pump 1) |
| P2Er | No detection of current change when turning on and off (Pump 2) |
| P3Er | No detection of current change when turning on and off (Pump 3) |
| CPEr | No detection of current change when turning on and off (Circ Pump) |
| bLEr | No detection of current change when turning on and off (Blower) |
| FnErP | No detection of current change when turning on and off (Fan) |
| Sc | The system is scanning all outputs to learn the current draw of every accessory |
| ScEr | A scan error was detected (System learning error) |
| LL- – | Low level software setting |
| Ph-xP | Number of phases (Incoming power) |
| br- – | Breaker settings |
| IN.Xm2 | |
| Code | Fault |
| rHId | No match Between heater and pack models |
| nH | Trying to heat water but no heat increase detected |
| nF | No flow condition is detected |
| Hr | Hardware error detected (Stuck relay, thermal fuse) |
| HL | Hi-Limit circuit tripped (water has reached 50C or 122F) |
| OH | Overheat. (Water temp at 44.5C or 112.1F) |
| rHnC | Communication error- (Heater to controller) |
| Prr | Temperature sensor failed |
| AOH | Spa controller to hot |
| Spin | Input voltage too low |
| FLO | No Flow detected |
| FLC | Flow switch closed |
| F1 | Fuse #1 blown |
| F2 | Fuse #2 blown |
| F3 | Fuse #3 blown |
| ScEr | Scan error detected (System learning error) |
| FrEr | Input power frequency 50/60hz out of range |
| Sc | System scanning (1st power up) |
| bL | No firmware into system |
| P9 | Programming firmware into system |
| UP-Ld or UPL | No valid low level software uploaded |
| SP-OT | Temperature inside controller is too high |
